RESIZE2FS
Section: Maintenance Commands (8)
Updated: May 2010
Index
Return to Main Contents
NAME
resize2fs - ext2/ext3/ext4 file system resizer
SYNOPSIS
resize2fs
[
-fFpPM
]
[
-d
debug-flags
]
[
-S
RAID-stride
]
device
[
size
]
DESCRIPTION
The
resize2fs
program will resize ext2, ext3, or ext4 file systems. It can be used to
enlarge or shrink an unmounted file system located on
device.
If the filesystem is mounted, it can be used to expand the size of the
mounted filesystem, assuming the kernel supports on-line resizing. (As
of this writing, the Linux 2.6 kernel supports on-line resize for
filesystems mounted using ext3 only.).
The
size
parameter specifies the requested new size of the filesystem.
If no units are specified, the units of the
size
parameter shall be the filesystem blocksize of the filesystem.
Optionally, the
size
parameter may be suffixed by one of the following the units
designators: 's', 'K', 'M', or 'G',
for 512 byte sectors, kilobytes, megabytes, or gigabytes, respectively.
The
size
of the filesystem may never be larger than the size of the partition.
If
size
parameter is not specified, it will default to the size of the partition.
The
resize2fs
program does not manipulate the size of partitions. If you wish to enlarge
a filesystem, you must make sure you can expand the size of the
underlying partition first. This can be done using
fdisk(8)
by deleting the partition and recreating it with a larger size or using
lvextend(8),
if you're using the logical volume manager
lvm(8).
When
recreating the partition, make sure you create it with the same starting
disk cylinder as before! Otherwise, the resize operation will
certainly not work, and you may lose your entire filesystem.
After running
fdisk(8),
run resize2fs to resize the ext2 filesystem
to use all of the space in the newly enlarged partition.
If you wish to shrink an ext2 partition, first use
resize2fs
to shrink the size of filesystem. Then you may use
fdisk(8)
to shrink the size of the partition. When shrinking the size of
the partition, make sure you do not make it smaller than the new size
of the ext2 filesystem!
OPTIONS
- -d debug-flags
-
Turns on various resize2fs debugging features, if they have been compiled
into the binary.
debug-flags
should be computed by adding the numbers of the desired features
from the following list:
2 - Debug block relocations
4 - Debug inode relocations
8 - Debug moving the inode table
- -f
-
Forces resize2fs to proceed with the filesystem resize operation, overriding
some safety checks which resize2fs normally enforces.
- -F
-
Flush the filesystem device's buffer caches before beginning. Only
really useful for doing
resize2fs
time trials.
- -M
-
Shrink the filesystem to the minimum size.
- -p
-
Prints out a percentage completion bars for each
resize2fs
operation, so that the user can keep track of what
the program is doing.
- -P
-
Print the minimum size of the filesystem and exit.
- -S RAID-stride
-
The
resize2fs
program will heuristically determine the RAID stride that was specified
when the filesystem was created. This option allows the user to
explicitly specify a RAID stride setting to be used by resize2fs instead.
KNOWN BUGS
The minimum size of the filesystem as estimated by resize2fs may be
incorrect, especially for filesystems with 1k and 2k blocksizes.
AUTHOR
resize2fs
was written by Theodore Ts'o <tytso@mit.edu>.
COPYRIGHT
Resize2fs is Copyright 1998 by Theodore Ts'o and PowerQuest, Inc. All
rights reserved.
As of April, 2000
Resize2fs
may be redistributed under the terms of the GPL.
SEE ALSO
fdisk(8),
e2fsck(8),
mke2fs(8),
lvm(8),
lvextend(8)
Index
- NAME
-
- SYNOPSIS
-
- DESCRIPTION
-
- OPTIONS
-
- KNOWN BUGS
-
- AUTHOR
-
- COPYRIGHT
-
- SEE ALSO
-
This document was created by
man2html,
using the manual pages.
Time: 19:49:32 GMT, April 27, 2011