ADJTIMEX

Section: Linux Programmer's Manual (2)
Updated: 2004-05-27
Index Return to Main Contents
 

NAME

adjtimex - tune kernel clock  

SYNOPSIS

#include <sys/timex.h>

int adjtimex(struct timex *buf);  

DESCRIPTION

Linux uses David L. Mills' clock adjustment algorithm (see RFC 1305). The system call adjtimex() reads and optionally sets adjustment parameters for this algorithm. It takes a pointer to a timex structure, updates kernel parameters from field values, and returns the same structure with current kernel values. This structure is declared as follows:

struct timex {
    int modes;           /* mode selector */
    long offset;         /* time offset (usec) */
    long freq;           /* frequency offset (scaled ppm) */
    long maxerror;       /* maximum error (usec) */
    long esterror;       /* estimated error (usec) */
    int status;          /* clock command/status */
    long constant;       /* pll time constant */
    long precision;      /* clock precision (usec) (read-only) */
    long tolerance;      /* clock frequency tolerance (ppm)
                            (read-only) */
    struct timeval time; /* current time (read-only) */
    long tick;           /* usecs between clock ticks */
};

The modes field determines which parameters, if any, to set. It may contain a bitwise-or combination of zero or more of the following bits:

#define ADJ_OFFSET            0x0001 /* time offset */
#define ADJ_FREQUENCY         0x0002 /* frequency offset */
#define ADJ_MAXERROR          0x0004 /* maximum time error */
#define ADJ_ESTERROR          0x0008 /* estimated time error */
#define ADJ_STATUS            0x0010 /* clock status */
#define ADJ_TIMECONST         0x0020 /* pll time constant */
#define ADJ_TICK              0x4000 /* tick value */
#define ADJ_OFFSET_SINGLESHOT 0x8001 /* old-fashioned adjtime() */

Ordinary users are restricted to a zero value for mode. Only the superuser may set any parameters.
 

RETURN VALUE

On success, adjtimex() returns the clock state:

#define TIME_OK   0 /* clock synchronized */
#define TIME_INS  1 /* insert leap second */
#define TIME_DEL  2 /* delete leap second */
#define TIME_OOP  3 /* leap second in progress */
#define TIME_WAIT 4 /* leap second has occurred */
#define TIME_BAD  5 /* clock not synchronized */

On failure, adjtimex() returns -1 and sets errno.  

ERRORS

EFAULT
buf does not point to writable memory.
EINVAL
An attempt is made to set buf.offset to a value outside the range -131071 to +131071, or to set buf.status to a value other than those listed above, or to set buf.tick to a value outside the range 900000/HZ to 1100000/HZ, where HZ is the system timer interrupt frequency.
EPERM
buf.mode is nonzero and the caller does not have sufficient privilege. Under Linux the CAP_SYS_TIME capability is required.
 

CONFORMING TO

adjtimex() is Linux-specific and should not be used in programs intended to be portable. See adjtime(3) for a more portable, but less flexible, method of adjusting the system clock.  

SEE ALSO

settimeofday(2), adjtime(3), capabilities(7), time(7)  

COLOPHON

This page is part of release 3.27 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/.


 

Index

NAME
SYNOPSIS
DESCRIPTION
RETURN VALUE
ERRORS
CONFORMING TO
SEE ALSO
COLOPHON

This document was created by man2html, using the manual pages.
Time: 19:49:18 GMT, April 27, 2011